View AD7680BRM_6074675.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3 mw, 100 ksps, 16-bit adc in 6-lead sot-23 ad7680 rev. a information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent ri ghts of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.326.8703? 2004-2011 analog devices, inc. all rights reserved. features fast throughput rate: 100 ksps specified for v dd of 2.5 v to 5.5 v low power 3 mw typ at 100 ksps with 2.5 v supply 3.9 mw typ at 100 ksps with 3 v supply 16.7 mw typ at 100 ksps with 5 v supply wide input bandwidth 86 db snr at 10 khz input frequency flexible power/serial clock speed management no pipeline delays high speed serial interface spi?/qspi?/wire/dsp compatible standby mode: 0.5 a max 6-lead sot-23 and 8-lead msop packages applications battery-powered systems: personal digital assistants medical instruments mobile communications instrumentation and control systems remote data acquisition systems high speed modems optical sensors functional block diagram 03643-0-001 v in v dd gnd ad7680 sclk sdata cs t/h 16-bit successive approximation adc control logic figure 1. table 1. msop/sot-23 16-bit pulsar adc type/ksps 100 ksps 250 ksps 500 ksps true differential ad7684 ad7687 ad7688 pseudo differential ad7683 ad7685 ad7686 unipolar ad7680 general description the ad7680 is a 16-bit, fast, low power, successive approximation adc. the part operates from a single 2.5 v to 5.5 v power supply and features throughput rates up to 100 ksps. the part contains a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 7 mhz. the conversion process and data acquisition are controlled using cs and the serial clock, allowing the devices to interface with microprocessors or dsps. the input signal is sampled on the falling edge of cs and the conversion is also initiated at this point. there are no pipeline delays associated with the part. the ad7680 uses advanced design techniques to achieve very low power dissipation at fast throughput rates. the reference for the part is taken internally from v dd , which allows the widest dynamic input range to the adc. thus, the analog input range for this part is 0 v to v dd . the conversion rate is determined by the sclk frequency. product highlights 1. first 16-bit adc in a sot-23 package. 2. high throughput with low power consumption. 3. flexible power/serial clock speed management. the conversion rate is determined by the serial clock, allowing the conversion time to be reduced through the serial clock speed increase. this allows the average power consumption to be reduced when a power-down mode is used while not converting. the part also features a shutdown mode to maximize power efficiency at lower throughput rates. power consumption is 0.5 a max when in shutdown. 4. reference derived from the power supply. 5. no pipeline delays. this part features a standard successive approximation adc with accurate control of the sampling instant via a cs input and once-off conversion control.
ad7680 rev. a | page 2 of 24 table of contents specifications ..................................................................................... 2 ? specifications ..................................................................................... 4 ? timing specifications ....................................................................... 6 ? absolute maximum ratings ............................................................ 7 ? esd caution .................................................................................. 7 ? pin configurations and function descriptions ........................... 8 ? terminology ...................................................................................... 9 ? typical performance characteristics ........................................... 10 ? circuit information ........................................................................ 12 ? converter operation .................................................................. 12 ? analog input ............................................................................... 12 ? adc transfer function ................................................................. 13 ? typical connection diagram ................................................... 13 ? digital inputs .......................................................................... 13 ? modes of operation ....................................................................... 14 ? normal mode .............................................................................. 14 ? power-down mode .................................................................... 15 ? power vs. throughput rate ........................................................... 16 ? serial interface ................................................................................ 17 ? ad7680 to adsp-218x .............................................................. 18 ? application hints ........................................................................... 19 ? grounding and layout .............................................................. 19 ? outline dimensions ....................................................................... 20 ? ordering guide .......................................................................... 21 ? revision history 5/11rev. 0 to rev. a deleted the evaluating the ad7680 performance section ...... 19 changes to ordering guide .......................................................... 21 1/04revision 0: initial version
ad7680 rev. a | page 3 of 24 specifications 1 table 2. v dd = 4.5 v to 5.5 v, f sclk = 2.5 mhz, f sample = 100 ksps, unless otherwise noted; t a = t min to t max , unless otherwise noted parameter a, b versions 1 unit test conditions/comments dynamic performance f in = 10 khz sine wave signal-to-noise + distortion (sinad) 2 83 db min 85 db typ signal-to-noise ratio (snr) 2 84 db min 86 db typ total harmonic distortion (thd) 2 ?97 db typ peak harmonic or spurious noise (sfdr) 2 ?95 db typ intermodulation distortion (imd) 2 second-order terms ?94 db typ third-order terms ?100 db typ aperture delay 20 ns max aperture jitter 30 ps typ full power bandwidth 8 mhz typ @ ?3 db 2.2 mhz typ @ ?0.1 db dc accuracy no missing codes 15 bits typ integral nonlinearity 2 4 lsb typ offset error 2 1.68 mv max gain error 2 0.038 % fs max analog input input voltage ranges 0 to v dd v dc leakage current 0.3 a max input capacitance 30 pf typ logic inputs input high voltage, v inh 2.8 v min input low voltage, v inl 0.4 v max input current, i in 0.3 a max typically 10 na, v in = 0 v or v dd input capacitance, c in 2 , 3 10 pf max logic outputs output high voltage, v oh v dd ? 0.2 v min i source = 200 a output low voltage, v ol 0.4 v max i sink = 200 a floating-state leakage current 0.3 a max floating-state output capacitance 2 , 3 10 pf max output coding straight (natural) binary conversion rate conversion time 8 s max 20 sclk cycles with sclk at 2.5 mhz 9.6 s max 24 sclk cycles with sclk at 2.5 mhz track-and-hold acquisition time 1.5 s max 400 ns max sine wave input 10 khz throughput rate 100 ksps see the serial interface section power requirements v dd 4.5/5.5 v min/v max i dd digital i/p s = 0 v or v dd normal mode (static) 5.2 ma max sclk on or off. v dd = 5.5 v normal mode (operational) 4.8 ma max f sample = 100 ksps. v dd = 5.5 v; 3.3 ma typ full power-down mode 0.5 a max sclk on or off. v dd = 5.5 v power dissipation 4 v dd = 5.5 v normal mode (operational) 26.4 mw max f sample = 100 ksps full power-down 2.75 w max 1 temperature range as follows: b version: ?40c to +85c. 2 see the terminology section. 3 sample tested during initial release to ensure compliance. 4 see the power vs. throughput rate section.
ad7680 rev. a | page 4 of 24 specifications 1 table 3. v dd = 2.5 v to 4.096 v, f sclk = 2.5 mhz, f sample = 100 ksps, unless otherwise noted; t a = t min to t max , unless otherwise noted. parameter a version 1 b version 1 unit test conditions/comments dynamic performance f in = 10 khz sine wave signal-to-noise + distortion (sinad) 2 83 83 db min v dd = 4.096 v 82 82 db min v dd = 2.5 v to 3.6 v 86 86 db typ signal-to-noise ratio (snr) 2 84 84 db min v dd = 4.096 v 83 83 db min v dd = 2.5 v to 3.6 v 86 86 db typ total harmonic distortion (thd) 2 ?98 ?98 db typ peak harmonic or spurious noise (sfdr) 2 ?95 ?99 db typ intermodulation distortion (imd) 2 second-order terms ?94 ?94 db typ third-order terms ?100 ?100 db typ aperture delay 20 10 ns max aperture jitter 30 30 ps typ full power bandwidth 7 7 mhz typ @ ?3 db; v dd = 4.096 v 5 5 mhz typ @ ?3 db; v dd = 2.5 v to 3.6 v 2 2 mhz typ @ ?0.1 db; v dd = 4.096 v 1.6 1.6 mhz typ @ ?0.1 db; v dd = 2.5 v to 3.6 v dc accuracy no missing codes 14 15 bits min integral nonlinearity 2 3.5 3.5 lsb max v dd = 4.096 v 3 3 lsb max v dd = 2.5 v to 3.6 v offset error 2 1.25 1.25 mv max v dd = 4.096 v 1.098 1.098 mv max v dd = 2.5 v to 3.6 v gain error 2 0.038 0.038 % fs max analog input input voltage ranges 0 to v dd 0 to v dd v dc leakage current 0.3 0.3 a max input capacitance 30 30 pf typ logic inputs input high voltage, v inh 2.4 2.4 v min input low voltage, v inl 0.4 0.4 v max input current, i in 0.3 0.3 a max typically 10 na, v in = 0 v or v dd input capacitance, c in 2 , 3 10 10 pf max logic outputs output high voltage, v oh v dd ? 0.2 v dd ? 0.2 v min i source = 200 a output low voltage, v ol 0.4 0.4 v max i sink = 200 a floating-state leakage current 0.3 0.3 a max floating-state output capacitance 2 , 3 10 10 pf max output coding straight (natural) binary conversion rate conversion time 8 8 s max 20 sclk cycles with sclk at 2.5 mhz 9.6 9.6 s max 24 sclk cycles with sclk at 2.5 mhz track-and-hold acquisition time 1.5 1.5 s max full-scale step input 400 400 ns max sine wave input 10 khz throughput rate 100 100 ksps see the serial interface section
ad7680 rev. a | page 5 of 24 parameter a version 1 b version 1 unit test conditions/comments power requirements v dd 2.5/4.096 2.5/4.096 v min/max i dd digital i/ps = 0 v or v dd normal mode (static) 2.8 2.8 ma max sclk on or off; v dd = 4.096 v 2 2 ma max sclk on or off; v dd = 3.6 v normal mode (operational) 2.6 2.6 ma max f sample = 100 ksps; v dd = 4.096 v; 1.75 ma typ 1.9 1.9 ma max f sample = 100 ksps; v dd = 3.6 v; 1.29 ma typ full power-down mode 0.3 0.3 a max sclk on or off power dissipation 4 normal mode (operational) 10.65 10.65 mw max f sample = 100 ksps; v dd = 4.096 v 6.84 6.84 mw max f sample = 100 ksps; v dd = 3.6 v 3 3 mw typ v dd = 2.5 v full power-down 1.23 1.23 w max v dd = 4.096v 1.08 1.08 w max v dd = 3.6 v 1 temperature range as follows: a, b versions: ?40c to +85c. 2 see the terminology section. 3 sample tested during initial release to ensure compliance. 4 see the power vs. throughput rate section.
ad7680 rev. a | page 6 of 24 timing specifications 1 table 4. v dd = 2.5 v to 5.5 v; t a = t min to t max , unless otherwise noted. limit at t min , t max parameter 3 v 5 v unit description f sclk 2 250 250 khz min 2.5 2.5 mhz max t convert 20 t sclk 20 t sclk min t quiet 100 100 ns min minimum quiet time required between bus relinquish and start of next conversion t 1 10 10 ns min minimum cs pulse width t 2 10 10 ns min cs to sclk setup time t 3 3 48 35 ns max delay from cs until sdata three-state disabled t 4 3 120 80 ns max data access time after sclk falling edge t 5 0.4 t sclk 0.4 t sclk ns min sclk low pulse width t 6 0.4 t sclk 0.4 t sclk ns min sclk high pulse width t 7 10 10 ns min sclk to data valid hold time t 8 4 45 35 ns max sclk falling edge to sdata high impedance t power-up 5 1 1 s typ power up time from full power-down 1 sample tested during initial release to ensure compliance. all input signals are specified with tr = tf = 5 ns (10% to 90% of v dd ) and timed from a voltage level of 1.6 v. 2 mark/space ratio for the sc lk input is 40/60 to 60/40. 3 measured with the load circuit of figure 2 and defined as the time required for the output to cross 0.8 v or 2.0 v. 4 t 8 is derived form the measured time taken by the data outputs to change 0.5 v when loaded with the circuit of figure 2. the meas ured number is then extrapolated back to remove the effects of charging or discharging the 50 pf capacitor. this means that the time, t 8 , quoted in the timing characteri stics is the true bus relinquish time of the part and is inde pendent of the bus loading. 5 see power vs. throughput rate section. 03643-0-002 200 ai ol 200 ai oh 1.6v to output pin c l 50pf figure 2. load circuit for digital output timing specification
ad7680 rev. a | page 7 of 24 absolute maximum ratings table 5. t a = 25c, unless otherwise noted. parameter rating v dd to gnd ?0.3 v to +7 v analog input voltage to gnd ?0.3 v to v dd + 0.3 v digital input voltage to gnd ?0.3 v to +7 v digital output voltage to gnd ?0.3 v to v dd + 0.3 v input current to any pin except supplies 1 10 ma operating temperature range commercial (b version) ?40c to +85c storage temperature range ?65c to +150c junction temperature 150c sot-23 package, power dissipation 450 mw ja thermal impedance 229.6c/w jc thermal impedance 91.99c/w msop package, power dissipation 450 mw ja thermal impedance 205.9c/w jc thermal impedance 43.74c/w lead temperature, soldering vapor phase (60 secs) 215c infared (15 secs) 220c esd 2 kv 1 transient currents of up to 100 ma do not cause scr latch-up. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution esd (electrostatic discharge) sensitive device. electrosta tic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge with out detection. although this product features proprietary esd protection circuitry, permanent dama ge may occur on devices subjected to high energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality.
ad7680 rev. a | page 8 of 24 pin configurations and function descriptions 03643-0-003 cs sdata sclk 6 5 4 v dd 1 gnd 2 v in 3 ad7680 top view (not to scale) sot-23 figure 3. sot-23 pin configuration 03643-0-022 nc = no connect ad7680 msop top view (not to scale) v dd 1 gnd 2 gnd 3 v in 4 cs sdata nc sclk 8 7 6 5 figure 4. msop pin configuration table 6. pin function descriptions pin no. sot-23 pin no. msop mnemonic function 1 1 v dd power supply input. the v dd range for the ad7680 is from 2.5 v to 5.5 v. 2 2, 3 gnd analog ground. ground reference point for all circui try on the ad7680. all analog input signals should be referred to this gnd voltage. 3 4 v in analog input. single-ended analog inp ut channel. the input range is 0 v to v dd . 4 5 sclk serial clock. logic input. sclk pr ovides the serial clock for accessing data from this part. this clock input is also used as th e clock source for the ad7680's conversion process. 5 7 sdata data out. logic output. the conversion result from the ad7680 is provided on this output as a serial data stream. the bits are clocked o ut on the falling edge of the sclk input. the data stream from the ad7680 consists of four leading zeros followed by 16 bits of conversion data that are provided msb first. this will be followed by four trailing zeroes if cs is held low for a total of 24 sclk cycles. see the section. serial interface 6 8 cs chip select. active low logic input. this input provides the dual function of initiating conversions on the ad7680 and framing the serial data transfer. n/a 6 nc no connect. this pin should be left unconnected.
ad7680 rev. a | page 9 of 24 terminology integral nonlinearity this is the maximum deviation from a straight line passing through the endpoints of the adc transfer function. the endpoints of the transfer function are zero scale, a point 1/2 lsb below the first code transition, and full scale, a point 1/2 lsb above the last code transition. differential nonlinearity this is the difference between the measured and the ideal 1 lsb change between any two adjacent codes in the adc. offset error this is the deviation of the first code transition (00 . . . 000) to (00 . . . 001) from the ideal, i.e., agnd + 1 lsb. gain error this is the deviation of the last code transition (111 . . . 110) to (111 . . . 111) from the ideal (i.e., v ref ? 1 lsb) after the offset error has been adjusted out. track-and-hold acquisition time the track-and-hold amplifier returns to track mode at the end of conversion. the track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within 1 lsb, after the end of the conversion. see the serial interface section for more details. signal-to-(noise + distortion) ratio this is the measured ratio of signal-to-(noise + distortion) at the output of the adc. the signal is the rms amplitude of the fundamental. noise is the sum of all nonfundamental signals up to half the sampling frequency ( f s /2, excluding dc). the ratio depends on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. the theoretical signal-to-(noise + distortion) ratio for an ideal n-bit converter with a sine wave input is given by signal-to-(noise + distortion ) = (6.02 n + 1.76) db thus, for a 16-bit converter, this is 98 db. total harmonic distortion (thd) thd is the ratio of the rms sum of harmonics to the fundamental. for the ad7680, it is defined as 1 2 6 2 5 2 4 2 3 2 2 v vvvvv dbthd ++++ = log20)( where v 1 is the rms amplitude of the fundamental and v 2 , v 3 , v 4 , v 5 , and v 6 are the rms amplitudes of the second through the sixth harmonics. peak harmonic or spurious noise peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the adc output spectrum (up to f s /2, excluding dc) to the rms value of the fundamental. normally, the value of this specification is determined by the largest harmonic in the spectrum, but for adcs where the harmonics are buried in the noise floor, it is a noise peak. intermodulation distortion with inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at the sum and difference frequencies of mfa nfb where m , n = 0, 1, 2, 3. intermodulation distortion terms are those for which neither m nor n are equal to zero. for example, the second-order terms include (fa + fb) and (fa ? fb), while the third-order terms include (2fa + fb), (2fa ? fb), (fa + 2fb), and (fa ?2fb). the ad7680 is tested using the ccif standard where two input frequencies near the top end of the input bandwidth are used. in this case, the second-order terms are usually distanced in frequency from the original sine waves, while the third-order terms are usually at a frequency close to the input frequencies. as a result, the second- and third-order terms are specified separately. the calculation of the intermodulation distortion is as per the thd specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals expressed in dbs.
ad7680 rev. a | page 10 of 24 typical performance characteristics figure 5 shows a typical fft plot for the ad7680 at 100 ksps sample rate and 10 khz input frequency. figure 6 shows the signal-to-(noise + distortion) ratio performance versus the input frequency for various supply voltages while sampling at 100 ksps with an sclk of 2.5 mhz. figure 7 shows a graph of the total harmonic distortion versus the analog input frequency for various supply voltages, while figure 8 shows a graph of the total harmonic distortion versus the analog input frequency for various source impedances (see the analog input section). figure 9 and figure 10 show the typical inl and dnl plots for the ad7680. 03643-0-021 db ?140 ?120 ?100 ?80 ?60 ?40 ?20 ?160 0 10k 20k 30k 40k frequency (khz) 50k 0 v dd = 5v f sample = 100ksps f in = 10khz snr = 88.28db sinad = 87.82db thd = ?97.76db sfdr = ?98.25db figure 5. ad7680 dynamic performance at 100 ksps 03643-0-016 sinad (db) 80 10 input frequency (khz) 100 85 90 95 v dd = 2.5v v dd = 5.25v v dd = 4.75v v dd = 4.3v v dd = 3.6v v dd = 3.0v v dd = 2.7v f sample = 100ksps t a = 25c figure 6. ad7680 sinad vs. analog input frequency for various supply voltages at 100 ksps 03643-0-017 thd (db) 90 10 input frequency (khz) 100 100 95 105 110 v dd = 4.75v v dd = 4.3v v dd = 3.6v v dd = 3.0v v dd = 2.7v v dd = 2.5v v dd = 5.25v f sample = 100ksps t a = 25c figure 7. ad7680 thd vs. analog input frequency for various supply voltages at 100 ksps 03643-0-018 thd (db) 75 10 input frequency (khz) 100 95 100 80 90 85 105 110 f sample = 100ksps t a = 25c v dd = 4.75v r in = 10 r in = 50 r in = 100 r in = 1000 figure 8. ad7680 thd vs. analog input frequency for various source impedances
ad7680 rev. a | page 11 of 24 03643-0-019 inl error (lsb) ?1.0 0 10000 20000 30000 40000 50000 60000 code 70000 1.0 1.5 ?0.5 0.5 0 2.0 2.5 v dd = 3.0v temp = 25 c figure 9. ad7680 typical inl 03643-0-020 dnl error (lsb) ?1.0 ?1.5 0 10000 20000 30000 40000 50000 60000 code 70000 1.0 ?0.5 0.5 0 1.5 v dd = 3.0v temp = 25 c figure 10. ad7680 typical dnl
ad7680 rev. a | page 12 of 24 circuit information the ad7680 is a fast, low power, 16-bit, single-supply adc. the part can be operated from a 2.5 v to 5.5 v supply and is capable of throughput rates of 100 ksps when provided with a 2.5 mhz clock. the ad7680 provides the user with an on-chip track-and-hold adc and a serial interface housed in a tiny 6-lead sot-23 package or in an 8-lead msop package, which offer the user considerable space-saving advantages over alternative solutions. the serial clock input accesses data from the part and also provides the clock source for the successive approximation adc. the analog input range for the ad7680 is 0 v to v dd . an external reference is not required for the adc nor is there a reference on-chip. the reference for the ad7680 is derived from the power supply and thus gives the widest dynamic input range. the ad7680 also features a power-down option to save power between conversions. the power-down feature is implemented across the standard serial interface as described in the modes of operation section. converter operation the ad7680 is a 16-bit, successive approximation adc based around a capacitive dac. the ad7680 can convert analog input signals in the 0 v to v dd range. figure 11 and figure 12 show simplified schematics of the adc. the adc comprises control logic, sar, and a capacitive dac. figure 11 shows the adc during its acquisition phase. sw2 is closed and sw1 is in position a. the comparator is held in a balanced condition and the sampling capacitor acquires the signal on the selected v in channel. 03643-0-004 capacitive dac control logic sampling capacitor comparator acquisition phase a b sw1 v dd /2 sw2 v in figure 11. adc acquisition phase when the adc starts a conversion, sw2 opens and sw1 moves to position b, causing the comparator to become unbalanced ( figure 12 ). the control logic and the capacitive dac are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator back into a balanced condition. when the comparator is rebalanced, the conversion is complete. the control logic generates the adc output code (see the adc transfer function section). 03643-0-005 capacitive dac control logic sampling capacitor comparator conversion phase a b sw1 v dd /2 sw2 v in figure 12. adc conversion phase analog input figure 13 shows an equivalent circuit of the analog input structure of the ad7680. the two diodes, d1 and d2, provide esd protection for the analog inputs. care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 300 mv. this causes these diodes to become forward-biased and to start conducting current into the substrate. the maximum current these diodes can conduct without causing irreversible damage to the part is 10 ma. capacitor c1 in figure 13 is typically about 5 pf and can be attributed primarily to pin capacitance. resistor r1 is a lumped component made up of the on resistance of a track-and-hold switch. this resistor is typically about 25 . capacitor c2 is the adc sampling capacitor and has a capacitance of 25 pf typically. for ac applications, removing high frequency components from the analog input signal is recommended by use of an rc low-pass filter on the relevant analog input pin. in applications where harmonic distortion and signal-to-noise ratio are critical, the analog input should be driven from a low impedance source. large source impedances significantly affect the ac performance of the adc. this may necessitate the use of an input buffer amplifier. the choice of the op amp is a function of the particular application. when no amplifier is used to drive the analog input, the source impedance should be limited to low values. the maximum source impedance depends on the amount of total harmonic distortion (thd) that can be tolerated. the thd increases as the source impedance increases, and performance degrades (see figure 8 ). 03643-0-006 r1 c2 25pf conversion phase - switch open track phase - switch closed v in v dd c1 5pf d1 d2 figure 13. equivalent analog input circuit
ad7680 rev. a | page 13 of 24 adc transfer function the output coding of the ad7680 is straight binary. the designed code transitions occur at successive integer lsb values, i.e., 1 lsb, 2 lsbs. the lsb size is v dd /65536. the ideal transfer characteristic for the ad7680 is shown in figure 14. 03643-0-007 000...000 111...111 1 lsb = v dd /65536 1 lsb +v dd ?1 lsb analog input 0v 000...001 000...010 111...110 111...000 011...111 figure 14. ad7680 transfer characteristic typical connection diagram figure 15 shows a typical connection diagram for the ad7680. v ref is taken internally from v dd and as such should be well decoupled. this provides an analog input range of 0 v to v dd . the conversion result is output in a 24-bit word, or alternatively, all 16 bits of the conversion re sult may be accessed using a minimum of 20 sclks. this 20-/24-bit data stream consists of a four leading zeros, followed by the 16 bits of conversion data, followed by four trailing zeros in the case of the 24 sclk transfer. for applications where power consumption is of concern, the power-down mode should be used between conversions or bursts of several conversions to improve power performance (see the modes of operation section). in fact, because the supply current required by the ad7680 is so low, a precision reference can be used as the supply source to the ad7680. for example, a ref19x voltage reference (ref195 for 5 v or ref193 for 3 v) or an ad780 can be used to supply the required voltage to the adc (see figure 15). this configuration is especially useful if the power supply available is quite noisy, or if the system supply voltages are at some value other than the required operating voltage of the ad7680, e.g., 15 v. the ref19x or ad780 outputs a steady voltage to the ad7680. recommended decoupling capacitors are a 100 nf low esr ceramic (farnell 335-1816) and a 10 f low esr tantalum (farnell 197-130). 03643-0-008 ad7680 0v to v dd input v in sclk sdata serial interface ? c/ ? p cs v dd gnd 10 ? f tant 0.1 ? f 3v 10 ? f 0.1 ? f 5v supply ref193 figure 15. typical connection diagram digital inputs the digital inputs applied to the ad7680 are not limited by the maximum ratings that limit the analog inputs. instead, the digital inputs applied can go to 7 v and are not restricted by the v dd + 0.3 v limit as on the analog inputs. for example, if the ad7680 were operated with a v dd of 3 v, 5 v logic levels could be used on the digital inputs. however, it is important to note that the data output on sdata still has 3 v logic levels when v dd = 3 v. another advantage of sclk and cs not being restricted by the v dd + 0.3 v limit is that power supply sequencing issues are avoided. if one of these digital inputs is applied before v dd , then there is no risk of latch-up as there would be on the analog inputs if a signal greater than 0.3 v were applied prior to v dd .
ad7680 rev. a | page 14 of 24 modes of operation the mode of operation of the ad7680 is selected by controlling the (logic) state of the cs signal during a conversion. there are two possible modes of operation, normal and power-down. the point at which cs is pulled high after the conversion has been initiated determines whether or not the ad7680 enters power- down mode. similarly, if the ad7680 is already in power-down, cs can control whether the device returns to normal operation or remains in power-down. these modes of operation are designed to provide flexible power management options. these options can optimize the power dissipation/throughput rate ratio for differing application requirements. normal mode this mode provides the fastest throughput rate performance, because the user does not have to worry about the power-up times with the ad7680 remaining fully powered all the time. figure 16 shows the general diagram of the operation of the ad7680 in this mode. the conversion is initiated on the falling edge of cs as described in the section. to ensure that the part remains fully powered up at all times, serial interface cs must remain low until at least 10 sclk falling edges have elapsed after the falling edge of cs . if cs is brought high any time after the 10th sclk falling edge, but before the 20th sclk falling edge, the part remains powered up, but the conversion is terminated and sdata goes back into three-state. at least 20 serial clock cycles are required to complete the conversion and access the complete conversion result. in addition, a total of 24 sclk cycles accesses four trailing zeros. cs may idle high until the next conversion or may idle low until cs returns high sometime prior to the next conversion, effectively idling cs low. once a data transfer is complete (sdata has returned to three- state), another conversion can be initiated after the quiet time, t quiet , has elapsed by bringing cs low again. 03643-0-009 11 0 2 0 4 leading zeros + conversion result cs sclk s dat a figure 16. normal mode operation
ad7680 rev. a | page 15 of 24 power-down mode this mode is intended for use in applications where slower throughput rates are required. either the adc is powered down between each conversion, or a series of conversions may be performed at a high throughput rate, and then the adc is powered down for a relatively long duration between these bursts of several conversions. when the ad7680 is in power-down, all analog circuitry is powered down. to enter power-down, the conversion process must be interrupted by bringing cs high anywhere after the second falling edge of sclk and before the 10th falling edge of sclk as shown in . once figure 17 cs has been brought high in this window of sclks, the part enters power-down, the conversion that was initiated by the falling edge of cs is terminated, and sdata goes back into three-state. if cs is brought high before the second sclk falling edge, the part remains in normal mode and will not power down. this avoids accidental power-down due to glitches on the cs line. in order to exit this mode of operation and power up the ad7680 again, a dummy conversion is performed. on the falling edge of cs , the device begins to power up and continues to power up as long as cs is held low until after the falling edge of the 10th sclk. the device is fully powered up once at least 16 sclks (or approximately 6 s) have elapsed and valid data results from the next conversion as shown in . if figure 18 cs is brought high before the 10th falling edge of sclk, regardless of the sclk frequency, the ad7680 goes back into power-down again. this avoids accidental power-up due to glitches on the cs line or an inadvertent burst of 8 sclk cycles while cs is low. so although the device may begin to power-up on the falling edge of cs , it powers down again on the rising edge of cs as long as it occurs before the 10th sclk falling edge. 03643-0-010 sclk s dat a 1 2 10 20 three-state cs figure 17. entering power-down mode 03643-0-011 11 0 2 01 2 0 s dat a sclk cs invalid data valid data the part is fully powered up with v in fully acquired the part begins to power up t power up figure 18. exiting power-down mode
ad7680 rev. a | page 16 of 24 power vs. throughput rate by using the power-down mode on the ad7680 when not converting, the average power consumption of the adc decreases at lower throughput rates. figure 19 shows how as the throughput rate is reduced, the part remains in its shut-down state longer, and the average power consumption over time drops accordingly. for example, if the ad7680 is operated in a continuous sampling mode, with a throughput rate of 10 ksps and an sclk of 2.5 mhz (v dd = 3.6 v), and the device is placed in power- down mode between conversions, the power consumption is calculated as follows. the maximum power dissipation during normal operation is 6.84 mw (v dd = 3.6 v). if the power-up time from power-down is 1 s, and the remaining conversion time is 8 s, (using a 20 sclk transfer), then the ad7680 can be said to dissipate 6.84 mw for 9 s during each conversion cycle. with a throughput rate of 10 ksps, the cycle time is 100 s. for the remainder of the conversion cycle, 91 s, the part remains in power-down mode. the ad7680 can be said to dissipate 1.08 w for the remaining 91 s of the conversion cycle. therefore, with a throughput rate of 10 ksps, the average power dissipated during each cycle is (9/100) (6.84 mw) + (91/ 100) (1.08 w) = 0.62 mw figure 19 shows the power dissipation versus the throughput rate when using the power-down mode with 3.6 v supplies, a 2.5 mhz sclk, and a 20 sclk serial transfer. 03643-0-012 power (mw) 0.01 0 5 10 15 20 25 throughput (ksps) 30 35 40 45 50 0.1 1 10 v dd = 3.6v f sclk = 2.5mhz figure 19. power vs. throughput using power-down mode with 20 sclk transfer at 3.6 v
ad7680 rev. a | page 17 of 24 serial interface figure 20 shows the detailed timing diagram for serial interfacing to the ad7680. the serial clock provides the conversion clock and also controls the transfer of information from the ad7680 during conversion. the cs signal initiates the data transfer and conversion process. the falling edge of cs puts the track-and-hold into hold mode, takes the bus out of three-state, and samples the analog input. the conversion is also initiated at this point and requires at least 20 sclk cycles to complete. once 17 sclk falling edges have elapsed, the track-and-hold goes back into track mode on the next sclk rising edge. figure 20 shows a 24 sclk transfer that allows a 100 ksps throughput rate. on the 24th sclk falling edge, the sdata line goes back into three-state. if the rising edge of cs occurs before 24 sclks have elapsed, the conversion terminates and the sdata line goes back into three-state; otherwise sdata returns to three-state on the 24th sclk falling edge as shown in figure 20. a minimum of 20 serial clock cycles are required to perform the conversion process and to access data from the ad7680. cs going low provides the first leading zero to be read in by the microcontroller or dsp. the remaining data is then clocked out by subsequent sclk falling edges beginning with the second leading zero; thus the first falling clock edge on the serial clock has the first leading zero provided and also clocks out the second leading zero. if a 24 sclk transfer is used as in figure 20, the data transfer consists of four leading zeros followed by the 16 bits of data, followed by four trailing zeros. the final bit (fourth trailing zero) in the data transfer is valid on the 24th falling edge, having been clocked out on the previous (23rd) falling edge. if a 20 sclk transfer is used as shown in figure 21, the data output stream consists of only four leading zeros followed by 16 bits of data with the final bit valid on the 20th sclk falling edge. a 20 sclk transfer allows for a shorter cycle time and therefore a faster throughput rate is achieved. 03643-0-013 t quiet t convert t 1 t 8 t 7 t 5 t 6 t 3 t 4 4 leading zeros 3-state 3-state 0 zero zero zero db15 db1 db0 zero zero zero zero sclk 1234518192021222324 sdata 4 trailing zeros cs t 2 figure 20. ad7680 serial interface timing diagram24 sclk transfer 03643-0-014 t quiet t 6 t 5 t 7 t 8 t 4 t 3 t convert t 2 t 1 0 0 zero zero zero db15 db1 db0 sclk 12345181920 sdata cs 4 leading zeros 3-state 3-state figure 21. ad7680 serial interface timing diagram20 sclk transfer
ad7680 rev. a | page 18 of 24 it is also possible to take vali d data on each sclk rising edge rather than falling edge, since the sclk cycle time is long enough to ensure the data is ready on the rising edge of sclk. however, the first leading zero is still driven by the cs falling edge, and so it can be taken on only the first sclk falling edge. it may be ignored and the first rising edge of sclk after the cs falling edge would have the second leading zero provided and the 23rd rising sclk edge would have the final trailing zero provided. this method may not work with most microcontrollers/dsps but could possibly be used with fpgas and asics. ad7680 to adsp-218x the adsp-218x family of dsps can be interfaced directly to the ad7680 without any glue logic required. the sport control register should be set up as follows: tfsw = rfsw = 1, alternate framing invrfs = invtfs = 1, active low frame signal dtype = 00, right justify data slen = 0111, 8-bit data-words isclk = 1, internal serial clock tfsr = rfsr = 0, frame first word irfs = 0 itfs = 1 to implement the power-down mode, slen should be set to 0111 to issue an 8-bit sclk burst. the connection diagram is shown in figure 22 . the adsp-218x has the tfs and rfs of the sport tied together, with tfs set as an output and rfs set as an input. the dsp operates in alternate framing mode and the sport control register is set up as described. transmit and receive autobuffering is used in order to get a 24 sclk transfer. each buffer contains three 8-bit words. the frame synchroniza- tion signal generated on the tfs is tied to cs , and as with all signal processing applications, equidistant sampling is necessary. in this example, the timer interrupt is used to control the sampling rate of the adc. 03643-0-015 sclk ad7680* sdata cs adsp-218x* sclk *additional pins omitted for clarity dr rfs tfs figure 22. interfacing to the adsp-218x the timer register is loaded with a value that provides an interrupt at the required sample interval. when an interrupt is received, the values in the transmit autobuffer start to be transmitted and tfs is generated. the tfs is used to control the rfs and therefore the reading of data. the data is stored in the receive autobuffer for processing or to be shifted later. the frequency of the serial clock is set in the sclkdiv register. when the instruction to transmit with tfs is given, i.e., tx0 = ax0, the state of the sclk is checked. the dsp waits until the sclk has gone high, low, and high again before transmission starts. if the timer and sclk values are chosen such that the instruction to transmit occurs on or near the rising edge of sclk, the data may be transmitted or it may wait until the next clock edge.
ad7680 rev. a | page 19 of 24 application hints grounding and layout the printed circuit board that houses the ad7680 should be designed such that the analog and digital sections are separated and confined to certain areas of the board. this facilitates the use of ground planes that can be separated easily. a minimum etch technique is generally best for ground planes, because it gives the best shielding. digital and analog ground planes should be joined at only one place. if the ad7680 is in a system where multiple devices require an agnd to dgnd connection, the connection should still be made at one point only, a star ground point that should be established as close as possible to the ad7680. avoid running digital lines under the device because these couple noise onto the die. the analog ground plane should be allowed to run under the ad7680 to avoid noise coupling. the power supply lines to the ad7680 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. fast switching signals, such as clocks, should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. avoid crossover of digital and analog signals. traces on opposite sides of the board should run at right angles to each other, which reduces the effects of feedthrough on the board. a microstrip technique is by far the best but is not always possible with a double-sided board. in this technique, the component side of the board is dedicated to ground planes while the signals are placed on the solder side. good decoupling is also very important. all analog supplies should be decoupled with 10 f tantalum in parallel with 0.1 f capacitors to agnd, as discussed in the typical connection diagram section. to achieve the best performance from these decoupling components, the user should attempt to keep the distance between the decoupling capacitors and the v dd and gnd pins to a minimum, with short track lengths connecting the respective pins.
ad7680 rev. a | page 20 of 24 outline dimensions compliant to jedec standards mo-178-ab 10 4 0 seating plane 1.90 bsc 0.95 bsc 0.60 bsc 65 123 4 3.00 2.90 2.80 3.00 2.80 2.60 1.70 1.60 1.50 1.30 1.15 0.90 0 .15 max 0 .05 min 1.45 max 0.95 min 0.20 max 0.08 min 0.50 max 0.30 min 0.55 0.45 0.35 pin 1 indicator 12-16-2008-a figure 23. 6-lead small outline transistor package [sot-23] (rj-6) dimensions shown in millimeters compliant to jedec standards mo-187-aa 6 0 0.80 0.55 0.40 4 8 1 5 0.65 bsc 0.40 0.25 1.10 max 3.20 3.00 2.80 coplanarity 0.10 0.23 0.09 3.20 3.00 2.80 5.15 4.90 4.65 pin 1 identifier 15 max 0.95 0.85 0.75 0.15 0.05 10-07-2009-b figure 24. 8-lead micro small outline package [m sop] (rm-8) dimensions shown in millimeters
ad7680 rev. a | page 21 of 24 ordering guide model 1 temperature range linearity error (lsb) 2 package description package option branding ad7680arjz-reel7 ?40c to +85c 14 bits min 6-lead sm all outline transistor package (sot-23) rj-6 c40 ad7680arm ?40c to +85c 14 bits min 8-lead mini small outline package (msop) rm-8 cqa ad7680arm-reel ?40c to +85c 14 bits min 8-lead mini small outline package (msop) rm-8 cqa ad7680arm-reel7 ?40c to +85c 14 bits min 8-le ad mini small outline package (msop) rm-8 cqa ad7680armz ?40c to +85c 14 bits min 8-lead mini small outline package (msop) rm-8 c40 ad7680brjz-r2 ?40c to +85c 15 bits min 6-lead sma ll outline transistor package (sot-23) rj-6 c3h ad7680brjz-reel7 ?40c to +85c 15 bits min 6-lead small outline transistor package (sot-23) rj-6 c3h AD7680BRM ?40c to +85c 15 bits min 8-lead mini small outline package (msop) rm-8 cqb AD7680BRM-reel ?40c to +85c 15 bits min 8-lead mini small outline package (msop) rm-8 cqb AD7680BRM-reel7 ?40c to +85c 15 bits min 8-le ad mini small outline package (msop) rm-8 cqb AD7680BRMz ?40c to +85c 15 bits min 8-lead mi ni small outline package (msop) rm-8 c3h AD7680BRMz-reel ?40c to +85c 15 bits min 8-lead mini small outline package (msop) rm-8 c3h AD7680BRMz-reel7 ?40c to +85c 15 bits min 8-le ad mini small outline package (msop) rm-8 c3h 1 z = rohs compliant part. 2 linearity error here refers to no missing codes.
ad7680 rev. a | page 22 of 24 notes
ad7680 rev. a | page 23 of 24 notes
ad7680 rev. a | page 24 of 24 notes ? 2004-2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d03643-0-5/ 11(a)

▲Up To Search▲

Price & Availability of AD7680BRM

	To Download AD7680BRM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .